&run_setup
    lattice = comm-ring.lte,
    use_beamline = "RING",
    p_central_mev = 3.e3,
    parameters = %s.param,
    default_order = 3,
	random_number_seed = 42319111,
    semaphore_file = %s.done,
	output = %s.out,
	losses = %s.lost,
	centroid = %s.cen
&end

!------------------ Add WATCH elements to observe position at all BPMs
&insert_elements
	name = *,
	type = MONI,
	element_def = "wbpm: watch,filename=\"%s%03ld.w\",mode=\"centroid\",interval=1" !----- FA data = average 38 samples of F_rev
&end

!------------------ Split magnets into small pieces for accuracy
&alter_elements name=*, type=CSBEND, item=N_KICKS, value=25, allow_missing_elements=1 &end
&alter_elements name=*, type=KSEXT, item=N_KICKS, value=4, allow_missing_elements=1 &end
&alter_elements name=*, type=KQUAD, item=N_KICKS, value=25, allow_missing_elements=1 &end

!------------------  Include Synchrotron radiation for damping
&alter_elements name=*, type=CSBEND, item=SYNCH_RAD, value=1 &end
&alter_elements name=*, type=CSBEND, item=ISR, value=1 &end

!------------------ add DC kick
&alter_elements	name = QM1G4C05B, type=KQUAD, item=DX, value=2e-3 &end !-------- at position s=134 m

!------------------ add time dependent noise 10 Hz, 60 Hz, and 110 Hz
!&modulate_elements 
!	name = QM1G4C16A, type=KQUAD, item=DX, !-------- s=4xx m
!	filename = NoiseSDDS2.sdds, time_column = "t", amplitude_column = "Noise10Hz",
!	differential = 0, multiplicative = 0,
!&end

!&modulate_elements 
!	name = QM1G4C05B, type=KQUAD, item=DX, !-------- s=134 m
!	filename = NoiseSDDS2.sdds, time_column = "t", amplitude_column = "Noise60Hz",
!	differential = 0, multiplicative = 0,
!&end

!&modulate_elements 
!	name = QL3G2C01A, type=KQUAD, item=DX, ! s=32 m
!	filename = NoiseSDDS2.sdds, time_column = "t", amplitude_column = "Noise110Hz",
!	differential = 0, multiplicative = 0,
!&end

&twiss_output
	filename = "%s.twi",
	matched=1,
    statistics=1,
	radiation_integrals=1,
&end

&rf_setup ! remove RF from RING
	harmonic=1320,
	bucket_half_height=1,
	over_voltage=1,
&end

! Tracking: Number of turns 
&run_control
	n_passes = 380000,
&end

! Get COD 
&closed_orbit 
	closed_orbit_iterations=500
	output = %s.orb
	start_from_recirc=1
    fixed_length = 1 !!!! Should really always set this to 1
&end

! Tracking
&bunched_beam
       n_particles_per_bunch = 1,      
       use_twiss_command_values = 0,
	   centroid[0] = -0.004, -0.0001, 0.0, 0.0, 0.0, 0.0
&end

&track 
&end